Cadet The Com-Pak Bath Heater CB103T Guida alla Risoluzione dei Problemi Scaricare il pdf

OWNER’S GUIDE FOR MULTI-VOLT MODELS

The Com-Pak™ Bath Heater

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

The Com-Pak™ Bath Heater

■ Primary and secondary thermal

safeguards

•

High temperature manual reset

•

Over temperature one-time thermal device

■ Commercial grade steel element - painted to

resist rusting

■ Built-in controls

- Single pole thermostat

- 60 minute timer

■ Powder coat paint process eliminates

sharp cutting edges

■ Three year extended warranty on

element and motor

■ Factory tested

■ Multi-Volt configurations

120 or 240 Volt AC (1000 Watts)

*Factory set at 240-Volts

Tools Required:

Phillips Screwdriver

Straight Screwdriver

Wire Strippers

Utility Knife

4 1

/2" Wood Screws

3 Insulated Wire Connectors

1 Strain Relief Connector

WARNING

Turn the electrical power off at the electrical panel

board (circuit breaker or fuse box) and lock or tag

the panel board door to prevent someone from

turning on power while you are working on the

heater. Failure to do so could result in serious

electrical shock, burns, or possible death.

1. Read all instructions before using this heater.

2. Read all information labels. Verify that the electrical

supply wires are the same voltage as the heater.

3. All electrical work and materials must comply with the

National Electric Code (NEC), the Occupational Safety and

Health Act (OSHA), and all state and local codes.

4. Connect the grounding pigtail (copper wire) provided in

the wall can to the supply ground wire.

5. If you need to install a new circuit or need additional

wiring information, consult a qualified electrician.

6. Protect electrical supply from kinks, sharp objects, oil,

grease, hot surfaces or chemicals.

7. WARNING

Overheating or fire may occur. DO NOT install the heater in

a floor, in the ceiling, below a towel bar, behind a door, or

anywhere the air discharge may be blocked in any manner.

8. WARNING

Fire or explosion may occur. DO NOT install heater in any

area where combustible vapors, gases, liquids, or

excessive lint or dust are present.

9. WARNING

DO NOT install where heater is likely to get wet.

10. WARNING

Heater must be connected to a GFCI protected branch circuit.

11. WARNING

Burn Hazard. This heater is hot when in use. To avoid burns,

do not let bare skin touch hot surfaces. Use extreme caution

when any heater is used by or near children or invalids.

12. WARNING

Risk of Electrical Shock. DO NOT install the heater directly

above bathtub or sink. DO NOT install in shower stall area

(Manufacturer recommends a minimum 2 foot clearance).

13. WARNING

Risk of Electrical Shock. Connect grounding lead

to grounding wire provided. Keep all foreign objects

out of heater.

14. WARNING

Risk of Electrical Shock. Never place a switch where it can

be reached from the tub or shower enclosure.

15. WARNING

Risk of Fire. Do not block heater. Heater must be kept clear

of all obstructions: a minimum of 3 feet in front, 6 inches

above and on both sides. Heaters must be kept clean of lint,

dirt and debris. (See Maintenance Instructions).

Models:

CBC103TW or CB103T The Com-Pak Bathroom Heater

360-693-2505 Fax: 360-694-8668 P.O. Box 1675 Vancouver, WA 98668-1675

Features & Benefits

1/2” Depth

10” Width

12 5/8” Height

1 2 3 4 5 6 7 8 9 10

Sommario

Pagina 1 - The Com-Pak™ Bath Heater

OWNER’S GUIDE FOR MULTI-VOLT MODELSThe Com-Pak™ Bath HeaterSAVE THESE INSTRUCTIONSIMPORTANT INSTRUCTIONSThe Com-Pak™ Bath Heater Primary and secondar

Pagina 2 - IMPORTANT!

GarantíaCONSULTE LOS CÓDIGOS ELÉCTRICOS LOCALES PARA DETERMINAR QUÉ TRABAJOS DEBEN SER REALIZADOS POR PERSONAL DE SERVICIO ELÉCTRICO CALIFICADO.Síntom

Pagina 3 - Figure 8

Installation InstructionsHow do I install for new construction?Figure 1Face of wall can mustextend 1/2 or 5/8 inch fromface of stud to allow forthickn

Pagina 4 - Figure 10

Installation InstructionsWARNINGTurn the electricalpower off at theelectrical panelboard (circuitbreaker or fusebox) and lock ortag the panel boarddoo

Pagina 5 - IMPORTANT INSTRUCTIONS

Operation & MaintenanceHow to operate your heater1. Once installation is complete and power has been restored, turn thethermostat knob fully clock

Pagina 6 - CONSERVE ESTAS INSTRUCCIONES

WarrantyCONSULT LOCAL ELECTRICAL CODES TO DETERMINE WHAT WORK MUST BE PERFORMED BY QUALIFIED ELECTRICAL SERVICE PERSONNEL.Symptom Problem SolutionBrea

Pagina 7 - Figura 3

GUÍA DEL PROPIETARIO PARA MODELOS DE MULTIVOLTAJEThe Com-Pak™ Bath HeaterCONSERVE ESTAS INSTRUCCIONESINSTRUCCIONES IMPORTANTESThe Com-Pak Bath Heater

Pagina 8 - Figura 8

Instrucciones para la instalación¿Cómo se instala el calentador en una construcción nueva?Figura 1La superficie de lacámara de pared debesobresalir de

Pagina 9 - Figura 10

Instrucciones para la instalación¡ADVERTENCIA!Desconecte laelectricidad en eltablero del paneleléctrico (caja decortacircuitos ofusibles) y trabe ocol

Pagina 10 - INSTRUCCIONES IMPORTANTES

Funcionamiento y mantenimientoCómo hacer funcionar el calentador 1. Una vez que se haya realizado la instalación y restablecido la energía eléctrica,g

Più documenti per Riscaldatori e bollitori per acqua Cadet The Com-Pak Bath Heater CB103T

Per vedere il documento Cadet The Com-Pak Bath Heater CB103T Istruzioni per gli Interventi

Cadet The Com-Pak Bath Heater CB103T Istruzioni per gli Interventi (12 pagine)

Commenti su questo manuale

Nessun commento

Cadet The Com-Pak Bath Heater CB103T Guida alla Risoluzione dei Problemi

Navigare online o scaricare Guida alla Risoluzione dei Problemi per Riscaldatori e bollitori per acqua Cadet The Com-Pak Bath Heater CB103T. Cadet The Com-Pak Bath Heater CB103T Troubleshooting guide Manuale Utente

Sommario

Più documenti per Riscaldatori e bollitori per acqua Cadet The Com-Pak Bath Heater CB103T

Commenti su questo manuale

Prodotti e manuali riguardandi Riscaldatori e bollitori per acqua Cadet The Com-Pak Bath Heater CB103T